edgeboard connectors, dual readout www.vishay.com for technical questions, contact: connectors@vishay.com document number: 36003 8 revision: 16-feb-09 eb7d vishay dale electrical specifications current rating: 5 a test voltage between contacts: at sea level: 1800 v rms at 70 000 feet (21 336 meters): 450 v rms insulation resistance: 5000 m minimum at 500 v dc potential contact resistance: 30 mv maximum at rated current (with gold plating) operating temperature: - 55 c to + 125 c humidity: 96 h at 90 % relative humidity at + 40 c, dried at room temperature for 3 h minimum, insulation resistance was greater than 5000 m durability: after 500 cycles of inse rtion and withdrawal of a 0.070" (1.78 mm) thick steel te st gauge, contact resistance less than 0.030 v at 5 a and indi vidual contact retention force when measured with 0.054" (1.37 mm) thick steel test slug greater than ? oz. shock: three 50g shocks in each of 3 mutually perpendicular planes with no loss of continuity vibration: 2 h in each of 3 mutually perpendicular planes, frequency sweep 10 cps to 55 cps at 0.06 double amplitude with no loss of continuity physical specifications contact type: bifurcated bellows number of contacts: 6, 10, 12, 15, 18, 22, 36, 43 per side contact spacing: 0.156" (3.96 mm) center to center card thickness: 0.054" to 0.071" (1.37 mm to 1.80 mm) card slot depth: dual readout = 0.260" (6.60 mm) note ? high temperature burn-in, edgeboard connectors, 0.156" (3.96 mm) center to center are on www.vishay.com/doc?36006 features ? 0.156" c-c x 0.140" grid (3.96 mm x 3.56 mm) ? bifurcated bellows contacts provide 2 flexing contact surfaces to assure positive contact under adverse conditions such as vibration or pc board irregularities ? accepts pc board thickness of 0.054" to 0.071" (1.37 mm to 1.80 mm) ? polarization between contact positions in all sizes. between contact polarization permits polarizing without loss of contact position ? selective gold plating ? polarizing key is reinforced nylon, may be inserted by hand, requires no adhesive. ? protected entry, provided by recessed leading edge of contact, permits the card slot to straighten and align the board before electrical contact is made. prevents damage to contact which might be caused by warped or out of tolerance boards ? recognized under the component program of underwriters laboratories, inc. listed under file e65524, project 77ch3889 applications for use with 0.062" (1.57 mm) printed circuit boards requiring an edgeboard type connector on 0.156" (3.96 mm) centers material specifications body: (standard) glass-filled phenolic per mil-m-14, dark green, flame retardant (ul 94 v-0). (optional - see ordering information) ?1? glass-filled diallyl phtala te per mil-m-14, type sdg-f green, flame retardant (ul 94 v-0) ?3? thermoplastic polyester, glass-filled, black, flame retardant (ul 94 v-0) ?5? thermoplastic polyphenylene sulfied, glass filled, brown, flame retardant (ul 94 v-0) contacts: phosphor bronze polarizing key: glass reinforced nylon, flame retardant (ul 94h-b) contact plating: gold (see ordering information) ordering information eb7 1 d b a 22 sg x a model body material optional body material 1 = diallyl phthalate 3 = glass-filled polyester 5 = glass-filled polyphenylene sulfied = omit number for standard pheniolic dual readout optional contacts beryllium copper copntacts optional available in ?a? and ?e? contact styles only (omit for standard) standard terminal variations a, e, c, or k contacts per side 6, 10, 12, 15, 18, 22, 36, or 43 contact plating sg = selective gold plating (0.00003" (0.000762 mm) minimum thick) on contact area with gold flash on terminal sgf = selective gold plating (0.000010" (0.000254 mm) minimum thick) on contact area with gold flash on terminal. all gold plating over 0.00005" (0.00127 mm) minimum nickel underplate. contact factory for additional plating options. mounting variations polarizing key positions key(s) are located to right of position(s) designated. required only when polarizing keys are to be factory installed
document number: 36003 for technical questions, contact: connectors@vishay.com www.vishay.com revision: 16-feb-09 9 eb7d edgeboard connectors, dual readout vishay dale dimensions in inches (millimeters) section c to c: polarizing key: when ordering polarizi ng keys individually, specify by the model number: pk-7 between contacts. hand insertion tool, tpk-7, provided upon request. # of contact positions per side abdef 6 1.78 (45.21) 1.53 (38.86) 1.22 (30.99) 1.10 (27.94) 0.328 (8.33) 10 2.41 (61.21) 2.16 (54.86) 1.84 (46.74) 1.72 (43.69) 0.328 (8.33) 12 2.72 (69.09) 2.47 (62.74) 2.16 (54.86) 2.04 (51.82) 0.328 (8.33) 15 3.19 (81.03) 2.94 (74.68) 2.62 (66.55) 2.50 (63.50) 0.328 (8.33) 18 3.66 (92.96) 3.41 (86.61) 3.09 (78.49) 2.97 (75.44) 0.328 (8.33) 22 4.28 (108.71) 4.03 (102.36) 3.72 (94.49) 3.60 (91.44) 0.328 (8.33) 36 6.53 (165.86) 6.22 (157.99) 5.91 (150.11) 5.78 (146.81) 0.438 (11.13) 43 7.62 (193.55) 7.30 (185.42) 7.00 (177.80) 6.80 (172.72) 0.500 (12.70) c c a b d e 0.062 0.010 (1.57 0.254) r typ. see table for mountin g variations see table for terminal variations 0.156 0.005 (3.96 0.127) non-cumulative 0.250 (6.35) 0.440 (11.1 8 ) 0.030 (0.762) f 0.010 ( 0.254) type ?a? 0.054 to 0.071 (1.37 to 1. 8 0) 0.260 (6.60) depth of card insertion 0.250 (6.35) types ?c? and ?k? 0.054 to 0.071 (1.37 to 1. 8 0) 0.260 (6.60) depth of card insertion 0.140 (3.56) 0.02 8 (0.711) 0.245 (6.22) 0.230 (5. 8 4)
www.vishay.com for technical questions, contact: connectors@vishay.com document number: 36003 10 revision: 16-feb-09 eb7d vishay dale edgeboard connectors, dual readout mounting variations in inches (millimeters) terminal variations in inches (millimeters) type g c 0.125 0.015 (3.18 0.381) k 0.200 0.015 (5.08 0.381) type ?v? clearance hole 0.250 (6.35) ref. 0.142 (3.61) dia. type ?vi? clearance hole no mountin g pad 0.250 (6.35) ref. 0.142 (3.61) dia. 0.220 (5.59) ref. type ?w? no mountin g flan g e 0.010 (0.254) 0.000 (0.000) type ?x? clearance hole 0.250 (6.35) ref. 0.12 8 (3.25) dia. type ?xi? clearance hole no mountin g pad 0.250 (6.35) ref. 0.220 (5.59) ref. 0.12 8 (3.25) dia. type ?y? threaded insert 0.250 (6.35) ref. 0.21 8 (5.54) ref. 4-40 unc-2b type ?z? floatin g bushin g radial float 0.047 (1.19) note: o v erall b ody length increased b y 0.060 (1.52) 0.250 [6.35] dia. 0.250 (6.35) ref. 0.116 (2.95) dia. 0.270 (6. 8 6) type ?a? pierced to fit 3, #22 awg wires 0.0 8 6 x 0.00 8 (2.1 8 x 0.203) 0.220 0.015 (5.59 0.3 8 1) type ?c? and ?k? solder dip to fit 0.051 (1.30), min. throu g h hole g see table 0.140 0.015 (3.56 0.3 8 1) type ?e? card extender 0.200 0.015 (5.0 8 0.3 8 1) 0.100 (2.54) 0.050 (1.27) 120 typ. 15 typ. 0.0 8 6 (2.1 8 ) uses type ?a? contact
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
